@article { author = {Kaviani, Azita and Dabaghi Tabriz, Fatemeh and Alinejad, Hengameh and Esfandiari, Mahsa}, title = {An in vitro Comparison of Microleakage in Composite Inlays with Two Different Methods of Surface Treatment}, journal = {Jundishapur Scientific Medical Journal}, volume = {12}, number = {1}, pages = {91-98}, year = {2013}, publisher = {Ahvaz Jundishapur University of Medical Sciences}, issn = {2252-052X}, eissn = {2252-0619}, doi = {}, abstract = {Background and Objective: In order to establish micromechanical retention, the internal surface of indirect composite restoration must be made before submitted to treatment. The aim of this in vitro investigation was to compare of microleakage in direct composite inlay restoration between two different surface treatments. Materials and Methods: Using75 extracted non-carious human premolars, following cavity preparation, all samples were restored by composite inlays after removal of inlays. The samples were randomly divided into 3 groups (n=25), according to the following surface treatment methods: sand blasting with 50 mm Al2O3 particles, etching with 9.5 % hydrofluoric acid  and non-treated control groups. All inlays were cemented to the tooth cavities with dual cure cement. The samples were thermocycled (500 cycles at 5-55°C), sectioned and extent of dye penetration at gingival margins was scored be two independent operators. The data were statically analyzed with Kruskal Wallis and Mann-Whitney tests. Results: Air abrasion resulted in a significant decrease in microleakage among all groups (P=0.030). Sand blasting led to less microleakage compared to hydrofluoric acid treatment (P=0.0385) and control (P=0.008). No significant difference was observed between hydrofluoric acid and control group. Conclusion: Sand blasting resulted in a significant reduction in microleakage, in composite inlays.}, keywords = {Microleakage,Composite inlay,surface treatment,Sand blast,Hydrofluoric acid}, title_fa = {بررسی آزمایشگاهی ریزنشت اینله‌های ساخته شده از کامپوزیت رزین پس از استفاده از دو روش آماده‌سازی سطحی}, abstract_fa = {زمینه و هدف: برای افزایش­ گیر میکرو مکانیکی اینله­های کامپوزیتی، آماده­سازی سطح داخلی آن انجام می­گردد. هدف از این مطالعه بررسی مقایسه­ای میزان ریزنشت اینله­های کامپوزیتی با دو روش آماده­سازی سطحی می­باشد.  روش بررسی: از 75 دندان پره­مولر سالم انسانی اینله­های کامپوزیتی تهیه شد. پس از تراش حفره، همة نمونه­ها به صورت کامپوزیت غیرمستقیم ترمیم شدند. پس از برداشت اینله­ها، نمونه­ها بسته به نوع آماده­سازی به 3 گروه n=25)) تقسیم شدند: گروه ماسه­سایی با ذرات Al2O350 میکرونی، گروه اچ با اسید هیدروفلوریک5/9 درصد و گروه کنترل. اینله­ها توسط سمان رزینی سمان شدند. ترموسایکلینگ نمونه­های آماده شده در دمای  oC55-5 به تعداد 500 دور انجام شد. نمونه­های آماده شده برش داده شدند و زیر استریومیکروسکوپ ارزیابی شدند تا میزان نفوذ رنگ در دیواره­ها مشخص شود. داده­ها تحت آنالیز آزمونهای آماری کروسکال ویلاس و من­ویتنی قرار گرفتند. یافته­ ها: استفاده از ماسه­سایی جهت آماده­سازی سطحی موجب کاهش معنا­داری در میزان ریزنشت نسبت به گروه­های دیگر می­شود (030/0P=). همچنین مقایسة دو به دوی گروه­های مورد مطالعه نشان داد بین دو گروه ماسه­سایی و اسید هیدروفلوریک ( 0385/0P=) میزان ریزنشت با ماسه­سایی به حد قابل ملاحظه­ای کمتر بود. نتیجه­ گیری: نتایج مطالعة حاضر نشان­دهندة این­ است که ماسه­سایی به کمک ذرات Al2O3 موجب بیشترین کاهش در ریزنشت اینله­های کامپوزیتی در مقایسه با اسید هیدروفلوریک می­شود.}, keywords_fa = {ریزنشت,اینله‌های کامپوزیتی,آماده‌سازی سطحی,ماسه‌سایی,اسید هیدروفلوریک}, url = {https://jsmj.ajums.ac.ir/article_49296.html}, eprint = {https://jsmj.ajums.ac.ir/article_49296_8bf8ec945a571f9e4daed7fabf57dc12.pdf} }